MFlenses - Új élet a digitális korban
MFLenses 2026

Manuális fókuszú objektívek fóruma

Fedezd fel a régi objektívek világát javítási jegyzetekkel, valódi tesztképekkel és képekkel teli archív témákkal.

Fedezd fel a régi objektívek világát javítási jegyzetekkel, valódi tesztképekkel és képekkel teli archív témákkal.
Reflektorfény

Kiemelt partneri hely a fórum nyitólapján.

Tiny White Spots on Lens
Előző téma megtekintése :: Következő téma megtekintése  


Reply

I have an Auto Sears 55/1.4, the Tomioka-made one, that I've been cleaning up. It's all been going fairly well, but there are tiny white dots on the surface of the rear element that need to go. They are foreign deposits, not damage to the lens coating. They are slightly raised. I have tried the following chemicals and they won't budge:
-Isopropanol
-Acetone
-Vinegar
-Ammonia

At this point I'm looking for more ideas for chemicals I could safely use on lens coatings. I don't expect anyone to know what the heck these white dots are.



Reply

try zippo fluid , you might have some luck


Reply

The chemicals you've already tried should work for most things.
If they don't work I'd be tempted to try scraping with wood or plastic - something significantly softer than glass yet rigid enough to allow a sideways force.

Good luck!


Reply

Okay strange results. Attempting to pick at it with a plastic spudger (And isopropanol for lube) didn't work. Hitting it with naptha-based lighter fluid dissolved... something? The dots got smaller, and something followed the flow of the naptha and dried out on the lens. I had to chase it with more naptha and quickly follow up with isopropanol before it dried again. Follow up passes with naptha won't touch the remainder.

Can anyone sound off on trying mineral spirits? I imagine MEK is a no-go.


Reply

Mike Deep írta:
Okay strange results. Attempting to pick at it with a plastic spudger (And isopropanol for lube) didn't work. Hitting it with naptha-based lighter fluid dissolved... something? The dots got smaller, and something followed the flow of the naptha and dried out on the lens. I had to chase it with more naptha and quickly follow up with isopropanol before it dried again. Follow up passes with naptha won't touch the remainder.

Can anyone sound off on trying mineral spirits? I imagine MEK is a no-go.


MEK would be very similar to acetone, just a bit less volatile.
If naphtha has done something you could try toluene, aromatics typically have the best solvency of hydrocarbons, and toluene is the least volatile of those (other than the highly carcinogenic benzene).


Reply

This may sound stupid but have you tried water? Maybe with a mild detergent? You seem to be going for solvents but sometimes just water or a detergent is better.


Reply

monopix írta:
This may sound stupid but have you tried water? Maybe with a mild detergent? You seem to be going for solvents but sometimes just water or a detergent is better.


+1 Like 1 Like 1


Reply

monopix írta:
This may sound stupid but have you tried water? Maybe with a mild detergent? You seem to be going for solvents but sometimes just water or a detergent is better.


Water is a very effective solvent for many inorganic compounds, but it often leaves deposits. I'd recommend rinsing with a little distilled water & then an alcohol if you use it.


Reply

Why even try to remove, should be irrelevant for IQ. Just reduction of contrast by a tiny bit...


Reply

A closer photo would reveal it it's fungus -- which I doubt. I suspect it's something like paint -- which would be difficult to remove without damaging the coating. But as pointed out, those aren't going to make any difference anyway. We all have dust in our lenses, and this is about the same.


Reply

Some spots also appear to be on the mount.

Could well be paint as xkaes already suggested, or something more nasty if the lens was used in reverse for macro photography and exposed to some mishap.

The worst damage I can imagine would be close-up photography of a cut-off grinding disk working on metal. If not protected, that rain of molten metal grinding sparks literally melt themselves onto/into ceramics glaze & glass surfaces, although generally I wouldn't expect them to be white.


Reply

I think this has reached a conclusion. On closer inspection, I believe whatever the naptha dissolved had also pitted the lens coating, so the dots were still there, but fainter.

As for why I'm bothering, I know these wouldn't affect photos, but I'm trying to hold my refurbishments to a higher standard, as it's one of the few things I can work on in my current condition (quadrapelic, though functionality paraplegic now).


Reply

Late to the party here, but those spots are indeed fungus etching. The pits form at the origin point/center of the fungal colony.

Super common on these flat-backed Tomioka lenses. For some reason, the Cosinons and Mamiya/Sekors seem more prone to it than other brands. Guessing it has to do with the coatings used.